| Sample Modes | Real-Time Sample |
| Acquisition Modes |   |
| Normal | Normal data only |
| Peak Detect | High-frequency and randon glith capture |
| Average | Wavefom Average, selectable 4,8,16,32,64,128 |
| Inputs Coupling | AC, DC, GND |
| Inputs Impendance | 1MΩ±2% ‖ 20pF±3pF |
| Probe Attenuation | 1X, 10X |
| Supported Probe Attenuation Factor | 1X, 10X, 100X, 1000X |
| Maximum Input Voltage | CAT I and CAT II: 300VRMS (10×), Installation Category; CAT III: 150VRMS (1×) |
| Sample Rate Range | 1GS/s |
| Waveform Interpolation | (sin x)/x |
| Record Length | 2M |
| SEC/DIV Range | DSO1072E: 4ns/div~2000s/div, in a 2, 4, 8 sequence; DSO1102E: 2ns/div~2000s/div, in a 2, 4, 8 sequence |
| Sample Rate and Delay Time Accuracy | ±50ppm over any ≥ 1ms time interval |
| Scanning Speed Range | DSO1072E: 4ns/div to 8ns/div; (-8div x s/div) to 40ms; 20ns/div to 80μs/div;(-8div×s/div) to 40ms 200μs/div to 40s/div; (-8div×s/div) to 400s; DSO1102E: 2ns/div to10ns/div; (-4div×s/div) to 20ms; |
| Vertical Resolution | 8-bit resolution, all channel sampled simultaneously |
| Volts Range | 2mV/div to 10V/div at input BNC |
| Bandwidth | DSO1072E: 70MHz; DSO1102E: 100MHz; DSO1152E: 150MHz; DSO1202E: 200MHz |
| Rise Time at BNC( typical) | DSO1072E: 5ns; DSO1102E: 3.5ns; DSO1152E: 2.3ns; DSO1202E: 1.8ns |
| Math | +, -, *, /, FFT |
| FFT | Windows:Hanning, Flatop, Rectamgular, Bartlett, Blackman; 1024 sample point |
| Bandwidth Limit | 20MHz |
| Low Frequency Response (-3db) | ≤10Hz at BNC |
| DC Gain Accuracy | ±3% for Normal or Average acquisition mode, 100V/div to 10mV/div. ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div. |
| Trigger Types | Edge, Video, Pulse, Slope, Over time, Alternative |
| Trigger Source | CH1, CH2, AC Line |
| Trigger Modes | Auto, Normal, Single |
| Coupling Type | DC, AC, HF Reject, LF Reject, Noise Reject |
| Trigger Sensitivity (Edge Trigger Type) | DC(CH1,CH2): 1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full; AC: Attenuates signals below 10Hz ; HF Reject: Attenuates signals above 80kHz; LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz. |
| Trigger Level Range | CH1/CH2: ±8 divisions from center of screen; |
| Set Level to 50%(typical) | Operates with input signals ≥50Hz |
| Video Trigger |   |
| Video Trigger Type | CH1, CH2: Peak-to-peak amplitude of 2 divisions; |
| Signal Formats and Field Rates | Supports NTSC, PAL and SECAM broadcast systems for any field or any line |
| Holdoff Range | 100ns ~ 10s |
| Pulse Width Trigger |   |
| Pulse Width Trigger Mode | Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse |
| Pulse Width Range | 20ns ~ 10s |
| Slope Trigger |   |
HantekHTK-DSO1000ESERIES
Hantek DSO1000E Series
Five in one: Oscilloscope/Recorder/DMM/FFT Spectrum Analyzer/Frequency Counter.
Price on Request
1